![]() ![]() Step 1: Go to Tenant > Click on created tenant > click on tenant dropdown >click on Application Profile Dropdown you will see your configured application profile which you configured earlier. Configuring Cisco ACI – Creating EPG ( END POINT GROUP) Step 8 :- You can see created BD on Right Side. Step 7 :- In Step > 3 Advanced/ Troubleshooting click on Finish. Step 6:- In Create Subnet will define the gateway and scope of the network and click OK and then click on Next. Step 5: In Step >2 元 Configuration click on add subnet button and add subnet Step 4: Enter the Name of the BD and VRF in Step1 > Main and click next Step 3: Right click on Bridge Domain and create bridge domain. Step 1 :- Go to the Tenant tab > Tenant dropdown in left side navigation > Networking. Step 6:- Fill all the required field and then click submit.Ĭonfiguring Cisco ACI – Create Bridge Domain Step 4: Right Click on application Profile. ![]() Step 3:- Click on Tenant (Mgmt) dropdown arrow. Step 2 : Click on created Tenant like: I have create common, mgmt, infa tenant Configuring Cisco ACI – Create Application Profile Step 4: Fill all the required field and click on Submit. Step 1: Open ACI in browser and enter USERNAME and PASSWORD Step 2 :- Click on right corner below the node and schedule the upgrade. Step :- Go to Admin > Firmware > Infrastructure > Nodes. Step 3 :- Select the image location option from where you will fetch the image and then browse it. Step 2 :- Go to admin tab > Firmware > go to the right corner click on image and then click on setting and then click on add firmware to APIC. Step 1 :- Login APIC GUI using GUI Credential. Step 8 :- Now finally you can see that you node is completely register. Step 7 :- After that your register node will move from none pending Registration to Registration Node and it will see as an Inactive first, it will take time to come from Inactive to Active. ![]() it will shows Unknown first after registration. Step 6 :- After register you can see the Node ID, Name and Status. Step 5 :- Enter Node ID, Select Node and enter Node Name and click register. Step 4 :- Right click on discovered switch and click register. Step 3 :- Go to None Pending Registration and select the Node. Step 8:- And in the final step you will specify the admin credential. Step 7 :- Here you will specify the Out-Of-Band Management details and Interface Mode. This pool ACI will use for his own internal communication. Step 6 :- In this you will enter the VTEP IP Address pool. Step 5 :- In this Step you will specify that is this a active controller or standby controller. Step 4 :- Enter the POD ID, Single POD ID represent individual site. Step 3 :- In this you will specify who many active controller you have in the fabric, active controller can 3, 5 or 7. Step 2 :- In second step you will enter the fabric ID here. Initial Start-up configuration when configuring Cisco ACI The controller optimizes performance and manages and operates a scalable multitenant Cisco ACI fabric. It is the unified point of automation and management for the Cisco ACI fabric, policy enforcement, and health monitoring. The Cisco Application Policy Infrastructure Controller (Cisco APIC) is the main architectural component of the Cisco ACI solution. Create Attachable Access Entity Profilesīefore getting into Configuring Cisco ACI, let’s understand what the APIC is.Table of Contents – Configuring Cisco ACI We’ll end this part with a discussion on creation of physical domains. After that, we’ll configure the basic logical constructs such as tenant, application profile, bridge domain, end point group, etc. After that, we’ll head towards installing and upgrading the image on the APIC. Followed by that, we’ll get deeper into startup config, and discovery. Part 1 will cover the fundamentals of configuration. The table of content has been provided for your reference. The resource pool which comprises of L2/元 connectivity, infrastructure services (L4 to L7), Compute, Storage and virtualisation. The actual fabric which comprises of Cisco Nexus leaf / spine switches running the Cisco ACI mode operating system.ģ. An APIC cluster (Application Policy Infrastructure Controller) which defines policy models, and provides management, analytics and monitoring for the entire fabric.Ģ. It let’s the application requirements define the network.ġ. Before going deep into how to configure Cisco ACI (Network Centric Mode), let’s understand what Cisco ACI is.Ĭisco ACI (Application Centric Infrastructure) is Cisco’s Software Defined Networking Solution for the Data Center.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |